MR2 Spyder Flip Blade Key
Programming Instructions
Programming Instructions
STEP 1
REMOTE FOB programming
Before you begin, open the driver's door.
Make sure no key is in the ignition.
Complete these steps within 40 seconds.
1. Insert your master key into the ignition
and take it out, do it 2 times.
2. Close, then open the driver's door 2 times.
3. Insert the master key into the ignition
and take it out 1 time.
4. Close, then open the driver's door 2 times.
5. Insert the master key into the ignition
and leave it in.
6. Close the driver's door.
7. Turn the master key from LOCK to ON 1 time.
8. Remove the key from the ignition.
The signal lights will flash 1 time,
the buzzer chirps 1 time,
the doors will lock and unlock 1 time.
9. Press and hold both LOCK and UNLOCK buttons
on the new remote for 2 seconds then release.
11. Press and release the LOCK button
on the new remote 1 time.
The taillight and marker lights will flash 1 time
and buzzer will chirp 1 time.
The doors will lock and unlock.
12. open driver's door.
Programming complete.
Test the LOCK / UNLOCK / PANIC buttons.
REMOTE FOB programming
Before you begin, open the driver's door.
Make sure no key is in the ignition.
Complete these steps within 40 seconds.
1. Insert your master key into the ignition
and take it out, do it 2 times.
2. Close, then open the driver's door 2 times.
3. Insert the master key into the ignition
and take it out 1 time.
4. Close, then open the driver's door 2 times.
5. Insert the master key into the ignition
and leave it in.
6. Close the driver's door.
7. Turn the master key from LOCK to ON 1 time.
8. Remove the key from the ignition.
The signal lights will flash 1 time,
the buzzer chirps 1 time,
the doors will lock and unlock 1 time.
9. Press and hold both LOCK and UNLOCK buttons
on the new remote for 2 seconds then release.
11. Press and release the LOCK button
on the new remote 1 time.
The taillight and marker lights will flash 1 time
and buzzer will chirp 1 time.
The doors will lock and unlock.
12. open driver's door.
Programming complete.
Test the LOCK / UNLOCK / PANIC buttons.
STEP 2
TRANSPONDER programming
Before you begin,
make sure that the remote programming part
has been completed.
Next, get inside in the car and shut the doors.
1. Simultaneously press and release
the BRAKE and GAS PEDAL 1 time.
2. insert your master key into the ignition switch
and turn it to the ACCESSORY position.
3. press and release the GAS PEDAL 5 times.
4. press and release the BRAKE PEDAL 6 times.
5. Remove the master key.
6. Insert the NEW key.
7. Simultaneously press and release
the BRAKE and GAS PEDAL 1 time.
8. Observe the red security light
at the bottom center of your
A/C fan power dial.
It should be blinking red.
Within 80 seconds,
the blinking red light should stop.
That means the transponder chip
has been registered.
9. Remove the NEW key.
10. Step on the BRAKE PEDAL.
Programming complete.
Test the transponder programming.
When no key is in the ignition,
the red light should blink.
When the NEW key is in the ignition,
the red light will stop.
If the red light still blinks
when the NEW key is in the ignition,
start over.
TRANSPONDER programming
Before you begin,
make sure that the remote programming part
has been completed.
Next, get inside in the car and shut the doors.
1. Simultaneously press and release
the BRAKE and GAS PEDAL 1 time.
2. insert your master key into the ignition switch
and turn it to the ACCESSORY position.
3. press and release the GAS PEDAL 5 times.
4. press and release the BRAKE PEDAL 6 times.
5. Remove the master key.
6. Insert the NEW key.
7. Simultaneously press and release
the BRAKE and GAS PEDAL 1 time.
8. Observe the red security light
at the bottom center of your
A/C fan power dial.
It should be blinking red.
Within 80 seconds,
the blinking red light should stop.
That means the transponder chip
has been registered.
9. Remove the NEW key.
10. Step on the BRAKE PEDAL.
Programming complete.
Test the transponder programming.
When no key is in the ignition,
the red light should blink.
When the NEW key is in the ignition,
the red light will stop.
If the red light still blinks
when the NEW key is in the ignition,
start over.
STEP 3
KEY cutting
Before you begin, make sure that the remote and
transponder programming parts are successful.
Bring your original master key
and the NEW key
to your local locksmith to have the blade cut.
If you have any questions about the instructions,
please contact us at info@carsmodesign.com.
KEY cutting
Before you begin, make sure that the remote and
transponder programming parts are successful.
Bring your original master key
and the NEW key
to your local locksmith to have the blade cut.
If you have any questions about the instructions,
please contact us at info@carsmodesign.com.